How to Install Belgian Block Driveway Edging

Adding a neat row of Belgian block stones to each side of an asphalt driveway will boost its curb appeal while also providing a clear visual aid as you back out or pull in

An asphalt driveway often looks a little ragged around the edges, especially after a season's worth of snow, salt, and shoveling. Adding a neat row of Belgian block stones to each side will boost its curb appeal (no pun intended) while also providing a clear visual aid as you back out or pull in. As This Old House senior technical editor Mark Powers demonstrates, installing the blocks requires just a few basic tools and a rented saw for cutting through the asphalt. (A little muscle for lifting the blocks helps too.) Plant colorful flowers beside the edging when the weather warms up and you'll love how this project makes your whole front yard feel more spiffy.

Shown: 11x7x4 Belgian block stones, around $4 per block at stone yards.
 


Steps // How to Install Belgian Block Driveway Edging
1 ×

Overview of How To Install Belgian Block Driveway Edging

 
Step One // How to Install Belgian Block Driveway Edging

Overview of How To Install Belgian Block Driveway Edging

illustration of the process of adding stone edging to a pre-existing driveway
Illustration by Gregory Nemec

Project timeline:
Friday: Cut and prep the driveway's edges.
Saturday: Dig the trench and lay the stones.
Sunday: Finish laying the stones and backfill with soil.

 
2 ×

Secure a Chalk Line

 
Step Two // How to Install Belgian Block Driveway Edging

Secure a Chalk Line

person puts nails in concrete driveway next to chalk line
Photo by Kolin Smith

The edges of an asphalt driveway need to be cut straight so that the blocks line up evenly against it. Use a chalk line to mark the cuts. Lay a line near the edge of one side of the driveway. Next to the line, hammer nails partway into the asphalt, one at each end of the driveway and a few along its length, about 5 feet apart. Tie the line to the nail at one end, then pull the line taut as you loop it around the other nails along the edge, making sure it still rests on the asphalt's surface.

 
3 ×

Mark the Cut Line

 
Step Three // How to Install Belgian Block Driveway Edging

Mark the Cut Line

Mark Powers secures a chalk line on the edge of a driveway
Photo by Kolin Smith

Snap the chalk line between each secured point to leave a clear, straight mark to follow when cutting the asphalt.

 
4 ×

Cut the Edges

 
Step Four // How to Install Belgian Block Driveway Edging

Cut the Edges

Mark Powers saws into a concrete driveway
Photo by Kolin Smith

Using a concrete saw, cut the asphalt along the chalk line. Don't bother trying to hold the saw level; instead, let it sit on the asphalt and rock it forward to cut one small section at a time. To keep dust down, attach a hose to the fitting on the saw and run water through it as you cut, or have a helper hose down the asphalt in front of the blade while you're working. Repeat all steps for the other side of the driveway.

Tip: Don't let the saw penetrate the base course or soil under the asphalt, as this will dull the blade. Asphalt drives are usually 3 to 4 inches thick; gauge yours as you work so that your cuts don't go too deep.

 
5 ×

Remove Excess Asphalt

 
Step Five // How to Install Belgian Block Driveway Edging

Remove Excess Asphalt

man prying a spade between asphalt that's been cut and the excess asphalt
Photo by Kolin Smith

Wedge a spade into the cut line and pry the waste asphalt away from the side of the driveway.

 
6 ×

Break Up Waste Prior to Disposal

 
Step Six // How to Install Belgian Block Driveway Edging

Break Up Waste Prior to Disposal

Mark Powers chops excess asphalt into small chunks for easy removal
Photo by Kolin Smith

To make the asphalt easier to get rid of, split it into chunks about 1 foot long, using a brick set and a maul.

Tip: Most trash collectors won't take asphalt waste. To get rid of it, contact local asphalt producers; they often recycle it.

 
7 ×

Clean Up and Back-Cut the Rough Edges

 
Step Seven // How to Install Belgian Block Driveway Edging

Clean Up and Back-Cut the Rough Edges

removing rough edges from a newly cut asphalt driveway edge
Photo by Kolin Smith

In spots where the asphalt was thicker or wasn't cut cleanly, use a brick set and a maul to remove loose or stray chunks. Hold the brick set at an angle slightly off vertical as you work; this will undercut the surface slightly for better adhesion of the mortar. Repeat all steps for the other side of the driveway.

 
8 ×

Dig the Trench

 
Step Eight // How to Install Belgian Block Driveway Edging

Dig the Trench

Mark Powers digs a trench next to an asphalt driveway
Photo by Kolin Smith

Use a spade to dig a trench next to your driveway that's several inches wider than your blocks so that it can hold enough concrete to keep them in place. For stability, no more than half the blocks' height should project above the asphalt's surface, so the trench's depth should be at least half the blocks' height, plus 1 inch to make room for adding concrete below them. (For better drainage in areas prone to frost heave, dig the trench a bit deeper and tamp in a layer of crushed stone.)

 
9 ×

Stake a Level Line

 
Step Nine // How to Install Belgian Block Driveway Edging

Stake a Level Line

staking a level line for edging on an asphalt driveway
Photo by Kolin Smith

Drive a stake at each end of the trench. Measuring from the driveway's surface, mark the desired height of the blocks above the asphalt on both stakes. Tie a mason's line to one stake at the marked line, pull it taut, and secure it at the mark on the other stake. For long or unevenly pitched driveways, place additional stakes at the midpoint and as needed along the trench's length, and tie the line to each one at the proper height. Repeat all steps for the other side of the driveway.

 
10 ×

Add Concrete to a Short Section of the Trench

 
Step Ten // How to Install Belgian Block Driveway Edging

Add Concrete to a Short Section of the Trench

Mark adds concrete to the trench before laying in the first course of blocks
Photo by Kolin Smith

You'll install the edging in 5- to 10-block sections, filling the trench with concrete as you go. First, lay 5 to 10 blocks side by side next to the trench to determine the length of the first section. Mix concrete to a stiff consistency (it should hold together like a snowball if you ball it up in your hand). Using the spade, add a 1-inch layer to the first section of the trench.

 
11 ×

Install the First Run of Blocks

 
Step Eleven // How to Install Belgian Block Driveway Edging

Install the First Run of Blocks

pounding in the edging block with a rubber mallet
Photo by Kolin Smith

Set the first block in place, wiggling it into the concrete slightly until it's level and sits against the edge of the driveway. Tap the block with a rubber mallet until its top is even with the height of the level line. Repeat for the remaining blocks in the first section, making sure they're flush with the level line and one another.

 
12 ×

Add Concrete to Stabilize the Blocks

 
Step Twelve // How to Install Belgian Block Driveway Edging

Add Concrete to Stabilize the Blocks

adding concrete to the side of edging blocks for reinforcement
Photo by Kolin Smith

Using a mason's trowel, fill the trench behind the blocks with concrete, mixed to a stiff consistency, until it's level with or slightly higher than the asphalt's surface. With a pulling motion, smooth the concrete against the back of the blocks at an angle until the top of the concrete sits about 2 inches below the top of the blocks.

 
13 ×

Finish Installing the Edging

 
Step Thirteen // How to Install Belgian Block Driveway Edging

Finish Installing the Edging

Mark Powers installing edging blocks with a rubber mallet
Photo by Kolin Smith

Keep laying the blocks until the runs on both sides are done. Once all the blocks have been installed, use a push broom to sweep paver base into the joints between the blocks and between the blocks and asphalt. Backfill the trench with topsoil, which will help the concrete dry more slowly, resulting in a harder cure. Full curing may take up to a week, depending on the weather.

 
14 ×

Landscape the Border

 
Step Fourteen // How to Install Belgian Block Driveway Edging

Landscape the Border

finished driveway edging with flowers and shrubs planted on the side
Photo by Kolin Smith

When it's warm enough, add colorful flowers and plantings next to the edging. Avoid varieties with extensive root systems that could nudge the blocks out of place.

 
 
 

TV Listings

Find TV Listing for This Old House and Ask This Old House in your area.