Installing Inground Sprinklers tout
Steps // How to Install In-Ground Sprinklers
1 ×

In-ground Sprinkler Overview

Step One // How to Install In-Ground Sprinklers

In-ground Sprinkler Overview

sprinkler installation diagram
Illustration by Gregory Nemec

WARNING: Check with the local building department to obtain all necessary permits, and contact a one-call center to have the local utilities mark any buried electrical cables, gas lines, or

2 ×

Dig the Trenches

Step Two // How to Install In-Ground Sprinklers

Dig the Trenches

Digigng the trenches to install an in-ground sprinkler
Photo by Brian Smith

Locate the pipe for the water source that you'll be tapping into. It might be at the water meter in the basement or buried underground.

Mark the locations of all the trenches and sprinklers with wooden stakes or plastic flags.

Then use a gas-powered trenching machine to excavate the trenches to a depth of 4 to 12 inches, depending on the recommendation for your area of the country.

Tip: Most rental dealers will drop off and pick up the trenching machine for a small additional charge.

3 ×

Make the Water Connection

Step Three // How to Install In-Ground Sprinklers

Make the Water Connection

making the water connection when installing an in-ground sprinkler
Photo by Brian Smith

Turn off the water to the house at the meter.

Cut into the main water line and splice in a tee fitting with PVC cement and primer. If the line is copper, solder on a copper tee.

Glue a 90-degree PVC elbow onto a male PVC adapter.

Thread the adapter into the tee fitting installed on the main water line. It's okay to connect PVC to copper here.

TIP: If you are uncomfortable with this step, call in a professional plumber to tap into the main line for you.

4 ×

Install the Zone Valves

Step Four // How to Install In-Ground Sprinklers

Install the Zone Valves

Installing the zone valves when installing an in-ground sprinkler
Photo by Brian Smith

Dig a trench from the main water line to the valve box location, as indicated on your plan. At the end, dig a hole about 18 inches deep and 2 to 3 feet long.

Line the hole with 2 inches of gravel, then set the valve box into it. The box lid should be flush with the grass.

Next, following the manufacturer's directions, glue together the manifold and attach the zone valves. Set the manifold in the valve box.

Run 1-inch schedule 40 PVC pipe from the main water line to a backflow-prevention device and then connect it to the manifold.

Dig a shallow trench from the valve box to the location for the timer, according to your plan.

Lay the 24-volt underground wire in the trench and connect it to the wires leading from each valve.

5 ×

Place the Pipes in the Trenches

Step Five // How to Install In-Ground Sprinklers

Place the Pipes in the Trenches

Place the pipes in the trenches
Photo by Brian Smith

Following the plan, lay PVC pipe in all the trenches leading from the valve box. If necessary, join pipe sections with couplings and PVC cement.

Wherever a pipe branches off to a sprinkler head, splice in tee fittings, then attach a short length of flexible piping, which will connect to the sprinkler head.

Where a pipe connects to drip-irrigation tubing, attach an upturned elbow, a short vertical pipe, and a pressure reducer with a microfilter.

TIP: Save money and avoid extra trips to the home center by buying PVC fittings in multipiece contractor packs.

6 ×

Connect the Pipe at the Valve Box

Step Six // How to Install In-Ground Sprinklers

Connect the Pipe at the Valve Box

connecting the pipe at the valve box
Photo by Brian Smith

Use 90-degree elbows to join the PVC water pipes in the trenches to the zone valve pipes protruding from the valve box.

Once the piping is completed, turn on the water to flush any dirt or debris from the system. Turn the water off again to install the sprinklers.

7 ×

Install the Pop-up Sprinklers

Step Seven // How to Install In-Ground Sprinklers

Install the Pop-up Sprinklers

Install the pop-up sprinklers
Photo by Brian Smith

Attach a pop-up sprinkler onto the end of each length of flexible piping. Push the barbed fitting all the way into the pipe; no glue or hose clamp is needed.

Remove the cap from the sprinkler and install the appropriate spray nozzle, as indicated on the plan.

8 ×

Roll out the Irrigation

Step Eight // How to Install In-Ground Sprinklers

Roll out the Irrigation

Roll out the irrigation
Photo by Brian Smith

At flowerbeds and trees, connect drip-irrigation tubing to the pressure reducer and microfilter coming from the underground PVC pipes.

Roll out the tubing along the flower bed, keeping it close to the base of the plants.

Keep unwinding the spool back and forth throughout the flower bed; space the tubing 12 inches apart.

If necessary, join one length of tubing to another with a push-in coupling.

When you get to the end of the layout, cut the tubing with a utility knife if necessary, flush it with water, fold it over, and slip on an end clamp.

TIP: Set the tubing in the sun for a few hours and it will soften and be much easier to install.

9 ×

Install the Ground Stakes

Step Nine // How to Install In-Ground Sprinklers

Install the Ground Stakes

Installing the ground stakes
Photo by Brian Smith

Once all the irrigation tubing is laid out, secure it with plastic ground stakes. Hook each stake over the tubing and press it into the dirt .

Space the stakes about 18 to 24 inches apart.

Note that it's often necessary to place two stakes very close together and on opposite sides of the tubing to hold it down.

To prevent the water coming out of the drip-irrigation tubing from evaporating too quickly—and to help hide the tubing—cover the area with bark mulch. Spread it at least 4 inches deep and it will also deter weeds from sprouting.

10 ×

Connect the Timer Wires

Step Ten // How to Install In-Ground Sprinklers

Connect the Timer Wires

Connect the timer wires
Photo by Brian Smith

Mount the programmable timer on the house wall.

Strip the insulation from the ends of the 24-volt wires that lead from the zone valves to the timer.

Attach the wires to the timer terminals, as shown in the manufacturer's instructions.

Hire a licensed electrician to run power to the timer, if necessary.

Set the timer and run a test to make sure that each zone and all the sprinklers are operating properly.

Finally, adjust any nozzles that are spraying off course.


Shop Related Products


Sponsored Stories

TV Listings

Find TV listings for This Old House and Ask This Old House in your area.