filling up the hole around the dry-well with rounded stones

How to Install a Dry Well

Diverting roof runoff properly makes for a less slippery yard and walkway

Q: We have a downspout that dumps rainwater onto our front walkway, which in winter turns into a sheet of ice. Is there a way to fix this problem? —Tabby McCarthy, Olanthe, Kansas

Roger Cook replies: A wet walkway is not only a slipping hazard, it contributes to damaging frost heaves that can break apart pavement. If you can't relocate the downspout, route the water under your walk and out to a dry well buried in your lawn. This perforated, open-bottom plastic barrel, which sits in a hole and is surrounded by stones, captures water coming off your roof, and lets it slowly disperse into the ground. Your walkway will be drier, and your storm drains will be less overloaded.

To determine how many dry wells you'll need, enter your roof area and soil type into the calculator at NDS, Inc. When you're ready to start digging, follow the steps on the next page. After you're done, fit your gutters with leaf guards so that the dry well won't fill up with debris.

Shown: washed, rounded stones ensure that a dry well will disperse roof runoff properly into the ground.


Steps // How to Install a Dry Well
1 ×

Dig the Hole and Trench

 
Step One // How to Install a Dry Well

Dig the Hole and Trench

digging a hole for a dry well
Photo by Ryan Benyi

Coming out from the downspout, at least 10 feet from the foundation (and 3 feet from any property line), dig a hole about 4 feet deep and wide. With a long-handled shovel, tunnel under the sidewalk and dig a trench 1 foot deep and 6 inches wide that slopes gradually toward the hole. Shovel the soil onto a tarp. Save the sod to patch over the hole.

 
2 ×

Line the Hole

 
Step Two // How to Install a Dry Well

Line the Hole

the dry well hole lined with landscape fabric
Photo by Ryan Benyi

Line the hole with landscape fabric cut from a 6-foot-long roll. The material prevents soil from clogging the stones around the dry well. Leave enough fabric outside the hole so that you can cover the stones once the dry well is installed.

 
3 ×

Set Up the Pipe

 
Step Three // How to Install a Dry Well

Set Up the Pipe

connecting a downspout adaptor to a PVC elbow
Photo by Ryan Benyi

Buy enough 4-inch-diameter PVC pipe to reach from the end of the downspout to a point 14 to 16 inches into the hole. Also buy an elbow and a downspout adaptor (shown). Remove the existing elbow from the bottom of the downspout. Then, dry-fit the pieces and lay the pipe in the trench. Once you have a good fit, glue the pieces together with PVC cement.

 
4 ×

Check the Pitch

 
Step Four // How to Install a Dry Well

Check the Pitch

checking the pitch of the pipe that will drain water into the dry well
Photo by Ryan Benyi

The pipe should slope toward the dry well ¼ inch per foot of run. A 2-foot level will show a ½ inch gap under one end when held level. Adjust the pitch by adding or removing soil under the pipe. When the pitch is set, attach the adaptor to the downspout using stainless-steel sheet-metal screws, then backfill around the pipe. Trim the opposite end if it's too long.

 
5 ×

Install the Dry Well

 
Step Five // How to Install a Dry Well

Install the Dry Well

shoveling rounded stones into the dry well hole
Photo by Ryan Benyi

Assemble the dry well, then use a hammer to knock out all the 1½-inch-diameter drainage holes and one of the 4½-inch ports. Shovel a 6-inch-deep layer of washed, ¾-inch rounded stone into the hole. Set the dry well in the hole and slide the port over the PVC pipe. Center the dry well and fill around it with stone until you reach its top edge.

 
6 ×

Fit the Overflow Emitter

 
Step Six // How to Install a Dry Well

Fit the Overflow Emitter

checking with a level to see that the top of the overflow emitter is at ground level
Photo by Ryan Benyi

Using a reciprocating saw, cut a 4-inch hole in the dry well's lid and put the lid on. Take a length of 4-inch pipe and glue on an overflow emitter, which lets excess storm water escape. Trim the pipe so that the top of the emitter will sit at ground level when the pipe is glued to the lid. Cover the dry well with landscape fabric, and top it off with soil and sod.

 
 
 

TV Listings

Find TV Listing for This Old House and Ask This Old House in your area.