A circular saw is an essential tool for any do-it-yourself (DIY) enthusiast or professional carpenter. While you would mostly use it for cross-cutting, there are times when you need to make precise cuts along the length of the wood, known as rip cuts. This Old House contributor Mark Clement demonstrates how to create a straightedge guide for your circular saw to give you accurate and clean rip cuts every time.
Understanding Rip Cuts
Rip cuts are cuts made parallel to the wood grain, along the length of a board. While circular saws are designed for cross-cutting, you can adapt them for rip cuts with the right technique and accessories.
Pro Tip: Tom Silva, general contractor on This Old House, explains his straightedge method for rip cuts: “I’m gonna measure the side of the blade, to the side of the base plate. I know that’s an inch and a half offset.” He marks that offset on both ends of the workpiece, then clamps a piece of MDF with a factory edge along those marks to give the saw something straight to follow. “I’ve chosen a piece of MDF, and I’ve taken the factory edge because it’s nice and straight, no dips.”
Pro Tip: Norm Abram, master carpenter on This Old House, recommends attaching a rip fence to the shoe of your circular saw for accurate rip cuts: “This inexpensive T-shaped piece of metal rides against the edge of the workpiece, keeping the sawblade the same distance from the edge of the board throughout the cut.” To ensure safe, accurate rip cuts, Norm advises setting the blade-depth adjustment to cut about 1/8 inch deeper than the thickness of the board — this helps prevent the blade from binding.
Using the Saw Fence
Most circular saws come with a built-in fence accessory. To use it, do the following:
- Attach the fence to the front of the saw through the provided fittings
- Adjust the fence to the desired width of your cut
- Place the fence against the edge of your workpiece
- Guide the saw along the length of the board, keeping the fence flush against the edge
While this method works for basic cuts, it may not provide the precision you need for more detailed work.
Pro Tip: Norm Abram, in his “Circular-Saw Basics” column for This Old House Magazine, advises setting the blade so that its bottommost tooth is “⅛ to ¼ inch below the workpiece” before making any rip cut. “Always make sure the power source is unplugged before making any adjustments to the saw.”
The Importance of a Straight-edge Guide
For more precise cuts, a straight-edge guide, also known as a shoot board, is invaluable. This DIY tool allows you to do the following:
- Make perfectly straight cuts along the length of large boards
- Achieve consistent results on multiple pieces
- Improve accuracy beyond what the saw’s built-in fence can provide
Creating a DIY Straight-edge Guide
Making your own straight-edge guide is a simple process that can greatly enhance your circular saw’s capabilities. Here’s how to create one:
Materials Needed
- Plywood sheet (preferably with at least one factory-cut edge)
- Narrow strip of plywood (about two inches wide)
- Screws or narrow crown staples
- Circular saw
- Measuring tools (tape measure, combination square)
- Pencil for marking
Step-by-Step Guide
Pro Tip: Norm Abram, master carpenter on This Old House, recommends making the guide from ½-inch scrap plywood: “Take a piece of plywood 7 inches wider than the saw’s sole and cut a 2-inch strip off the factory edge. The remaining piece is the base. Snap a line on the base 5 inches from the edge you cut, then glue and screw the strip facedown, with the factory edge on the line.” Norm finds a 4-foot length especially useful for crosscutting plywood.
- Start with the factory-cut edge of your plywood sheet as your base
- Use a combination square to mark a line about two inches from the edge on both ends of the plywood
- Align your narrow strip of plywood with these marks
- Secure the strip to the base plywood using screws (every 12 inches) or narrow crown staples
- Set your circular saw to the proper depth to cut the plywood
- Place the shoe of the saw firmly against the newly attached strip
- Cut along the entire length of the plywood, creating a perfectly straight edge
This process creates a straight-edge guide that matches the exact cutting path of your saw, giving you precise cuts every time.
Using Your Straight-edge Guide
Now that you’ve created your straight-edge guide, it’s time to put it to use. Here’s how to make precise cuts using your new tool:
- Measure and mark your desired cut on the workpiece
- Align the cut edge of your straightedge guide with your marks
- Secure the guide to your workpiece using clamps on both ends
- Place your circular saw against the guide’s edge
- Make your cut, keeping the saw flush against the guide throughout the entire length
This method allows you to make precise cuts on large pieces that might not fit on a table saw, such as shelf blanks or cabinet sides.
Pro Tip: Tommy Silva, This Old House plumbing and heating expert, explains the key advantage of building a dedicated straightedge guide: “The beauty of this is that you can now lay the straight edge on the line. You cut, you don’t have to actually set it off right on the line. Clamp it down.” By trimming the base with your own saw, the guide’s edge becomes your exact cut line — no offset math required.
Tips for Perfect Cuts
For best results when using your straight-edge guide, always clamp your guide securely to prevent slipping during the cut and keep your saw’s base plate flat against the guide throughout the entire cut. Additionally, move the saw at a steady pace to avoid burn marks or rough edges. For longer cuts, use additional clamps in the middle of the guide for extra stability. Regularly check your guide for any wear or damage that might affect its accuracy.
Maintaining Your Straight-edge Guide
To keep your straight-edge guide in top condition, do the following:
- Store it flat to prevent warping
- Check the edge periodically for any nicks or damage
- Replace the guide if it becomes worn or damaged
- Keep the guide clean and free from sawdust buildup
Perform these routine checks to keep it accurate:
- Inspect the screws or staples to ensure they are secure
- Evaluate the guide’s alignment after several uses
- Clean the guide after each project to prevent buildup that might affect the precision
Alternative Straight-edge Options
While a DIY plywood guide is an excellent option, there are other straight-edge solutions available:
- Aluminum straight-edges: Lightweight and resistant to warping
- Clamping straight-edges: Feature built-in clamps for easy securing
- Steel straight-edges: Extremely durable but heavier to maneuver
- Track saw systems: Provide a guide and dust collection in one tool
Each option has its pros and cons, so choose the one that best fits your needs and budget.
Our Conclusion
Creating a straight-edge guide for your circular saw is a simple yet effective way to improve your woodworking skills. With this DIY tool, you can achieve precise, professional-quality rip cuts on various projects. Remember to always prioritize safety and maintain your tools for the best results.
