How to Clad a Wall in Stone

Use cast-concrete stone-veneer panels and masonry screws to dress up a plain wall

If pulling into your driveway causes you to cringe at the sight of an exposed foundation or a stretch of bare cinder block, why not cover it up? These panels of hand-painted cast concrete provide the look of handsomely stacked natural stone, and you don't need to hire a mason. In fact, you can install them on concrete or even framed walls with little more than a drill and a circular saw. Follow along as This Old House senior technical editor Mark Powers uses them to transform an unsightly eyesore into a front-yard focal point.

Shown: Stone-veneer panels: Versetta Stone Ledgestone in Terra Rosa finish, about $27 per panel; Boral USA


Steps // How to Clad a Wall in Stone
1 ×

Overview for How to Clad a Wall in Stone

 
Step One // How to Clad a Wall in Stone

Overview for How to Clad a Wall in Stone

wall clad in stone veneer connected to exterior of house
Illustration by Gregory Nemec

TIMELINE:
Day 1: Prep the site and install the first course (Steps 2–10).

Day 2: Finish and cap the wall (Steps 11–18).

 
2 ×

Measure the Wall

 
Step Two // How to Clad a Wall in Stone

Measure the Wall

man holds measuring tape up to corner of concrete block wall for how to clad a wall in stone
Photo by Kolin Smith

To calculate the number of universal corners to order, measure the height in inches of each outside wall corner, as shown, divide by 16, and round up to the nearest whole number. You'll fill the area between the corners with flat panels. To calculate how many you'll need, multiply the wall's width by its height in feet and divide the resulting area by 2 (each panel covers 2 square feet). Subtract the number of universal corners from the result, then add 10 percent to your order of flat panels. Add one universal corner to be safe.

 
3 ×

Paint the Bottom to Prep the Wall

 
Step Three // How to Clad a Wall in Stone

Paint the Bottom to Prep the Wall

hand spray paints the starter strip to match the palette of the stone panels for how to clad a wall in stone
Photo by Kolin Smith

The panels must be installed above ground level, resting on a plastic support called a starter strip, so you'll want to paint the wall below the strip to match the stone. Find a spray-paint color similar to the palette of your stone panels and paint the bottom few inches of the wall.

 
4 ×

Install the Starter Strip to Prep the First Course

 
Step Four // How to Clad a Wall in Stone

Install the Starter Strip to Prep the First Course

level used to set the starter strip for how to clad a wall in stone
Photo by Kolin Smith

Set the location for the starter strip, at least 2 inches above any soil. Here, the strip's lip aligns with the top of a stair on the adjacent side of the corner. Fit your drill/driver with a 3/16-inch masonry bit and drill a pilot hole through a slot in the strip near the corner and into the wall. Drive in a masonry screw to secure that end, then use the 4-foot level to bring the strip to level, and mark a line, as shown. Drill pilot holes and fasten the strip in two or three more spots, maintaining level.

 
5 ×

Remove the Tab

 
Step Five // How to Clad a Wall in Stone

Remove the Tab

a 5-in-1 tool removing tabs from the ends of panels that form a corner for how to clad a wall in stone
Photo by Kolin Smith

Flat panels have a tab on each side that meshes with slots on adjacent flat panels but needs to be removed from any end that forms a corner. Rest the panel faceup on a work surface and use the blade of the 5-in-1 tool to knock the tab off, as shown. The resulting flat edge will make for a tight corner.

 
6 ×

Mark the Panel

 
Step Six // How to Clad a Wall in Stone

Mark the Panel

a mason's pencil used to mark a panel's cutline for how to clad a wall in stone
Photo by Kolin Smith

Each run starts at a corner, with the finished end of a universal corner overlapping the end of a flat panel (with the tab removed). First, the universal corner is cut into two pieces; the finished edge of each piece starts a course, and the cut edge butts into a flat panel. For aesthetics, cut the universal corner so that each piece is at least 8 inches long. Or, as in our case, cut it to fit against the stair riser: Rest a flat panel on the adjacent side in the starter strip, then spin the universal corner upside down, butt its finished edge against the stair riser, and scribe a cutline, as shown.

 
7 ×

Cut to Length

 
Step Seven // How to Clad a Wall in Stone

Cut to Length

person wearing a mask and using a circular saw to cut the panel to length for how to clad a wall in stone
Photo by Kolin Smith

Rest the marked panel facedown on a work surface with scrap boards beneath it on either side of the cutline. Use a straightedge to mark a squared-off cutline along the narrowest point of the scribed line. Fit the circular saw with a segmented diamond blade and cut along the line, going through the concrete as well as the metal nailing strip. Be sure to wear safety glasses, a dust mask, and hearing protection.

 
8 ×

Fasten the First Panel

 
Step Eight // How to Clad a Wall in Stone

Fasten the First Panel

hands using a drill to create pilot holes for fastening the first panel for how to clad a wall in stone
Photo by Kolin Smith

Hold the cut universal corner against the wall, bringing its finished end flush with the face of the adjacent flat panel so that the two pieces form a 90° outside corner. Level the universal corner, and drill pilot holes through the nailing strip, as shown, directly through the metal if necessary, in at least two places. Fasten the panel with 1¼-inch self-tapping masonry screws.

Tip: Keep your bit spinning to remove dust as you back the drill out of the pilot hole, allowing the masonry screw to tap into the concrete.

 
9 ×

Finish the Run

 
Step Nine // How to Clad a Wall in Stone

Finish the Run

gloved hands attaching the last panel in the first course for how to clad a wall in stone
Photo by Kolin Smith

Continue installing full-size flat panels, working your way down the course. When you near the end, measure and cut a partial panel to fill the end of the course. If the cut piece has a tab on either side, use the 5-in-1 tool to knock it off. Fit the piece in place, drill pilot holes, and screw it to the wall.

 
10 ×

Install the Second Corner

 
Step Ten // How to Clad a Wall in Stone

Install the Second Corner

person installing the corner panel of the second course for how to clad a wall in stone
Photo by Kolin Smith

Use the cut half of the universal corner from the first course, positioned on the opposite side of the corner to stagger the joints. Slip the tongue on its bottom edge into the groove on top of the flat panel beneath. Position a flat panel, with its tab removed, atop the universal corner in the first course. Be sure it's cut to a different length than the piece beneath, to offset the joints across the wall. Mark and drill pilot holes for the universal corner, secure it, and install the adjacent flat panel to complete the corner.

 
11 ×

Align Adjacent Panels

 
Step Eleven // How to Clad a Wall in Stone

Align Adjacent Panels

using a drill to create pilot holes and align the panels for how to clad a wall in stone
Photo by Kolin Smith

Work along the course, brushing out debris from the top groove to ensure that the panels fit together snugly. As you set each new panel, make sure that it's aligned with the previous panel by nestling a ¼-inch metal rod in the groove along the top edge. The rod should lie flat and bridge the grooves in adjacent panels. If it doesn't, use the 5-in-1 tool to shim the panel up, or back several screws out of the previous panel and adjust it. When the panels align, drill pilot holes and fasten them to the wall.

 
12 ×

Stagger the Joints

 
Step Twelve // How to Clad a Wall in Stone

Stagger the Joints

hands using a mason's pencil to mark the nailing strip to stagger the joints for how to clad a wall in stone
Photo by Kolin Smith

If the end of a panel falls in line with a joint on any of the previous courses, you'll want to cut down its length slightly to maintain staggered joints. Hold the panel in place and mark the nailing strip at a different length. Transfer the mark to the back of the panel, cut it to size, and fasten it to the wall.

 
13 ×

Cut Panels to Fit the Top Course

 
Step Thirteen // How to Clad a Wall in Stone

Cut Panels to Fit the Top Course

person using a circular saw to cut the final course for how to clad a wall in stone
Photo by Kolin Smith

On the final course, you'll need to cut down the height of the panels to fit, removing the nailing strip so that the stone reaches to the top of the wall. Rest a flat panel in place and scribe a cutline on the back at the height of the wall. Set the panel on a work surface, and use the circular saw to cut it to the proper height. You may want to cut your corner pieces to length first, then cut them to the proper height, as shown. Dry-fit the two pieces at the corner to check the fit.

 
14 ×

Glue the Pieces

 
Step Fourteen // How to Clad a Wall in Stone

Glue the Pieces

applying glue to the panels using a caulk gun for how to clad a wall in stone
Photo by Kolin Smith

Remove the corner panels and apply straight beads of construction adhesive on the back of each piece in vertical runs, as shown, so that water is free to flow behind the panels and drain properly. Set the panels in place on the wall and adjust them to fit snugly at the corner.

 
15 ×

Sink the Fasteners

 
Step Fifteen // How to Clad a Wall in Stone

Sink the Fasteners

drilling holes to fix the fasteners for how to clad a wall in stone
Photo by Kolin Smith

To further secure the cut-down panels, locate several spots on each one where you can sink a fastener inconspicuously in joints between stones. Holding the piece in place, drill a pilot hole through the panel and into the wall. Drive in a masonry screw, sinking the head below the surface of the panel. Cover the screwheads with caulk, gather some dust from the cutting table, and blow it onto the drying caulk to camouflage it. You can touch up any gaps in the same manner. Finish installing the panels in the final course.

 
16 ×

Cut the Capstones

 
Step Sixteen // How to Clad a Wall in Stone

Cut the Capstones

a circular saw cutting the capstones for how to clad a wall in stone
Photo by Kolin Smith

Select a capstone several inches wider than the depth of your clad wall to create an overhang. Measure and mark the capstones to fit along the top of the wall. Use the circular saw and the segmented diamond blade to cut to length, as shown.

 
17 ×

Set the Stone to Cap the Wall

 
Step Seventeen // How to Clad a Wall in Stone

Set the Stone to Cap the Wall

setting the capstones on the top of the wall for how to clad a wall in stone
Photo by Kolin Smith

Working with a partner, lift the capstones and dry-fit them on top of the wall. Remove them and apply construction adhesive to the top of the wall and the edges of the veneer before resetting the stones; or, if you prefer an even more authentic look, set them in a stiff mortar bed. Now take a step back and marvel at the seamless look.

 
 
 

TV Listings

Find TV Listing for This Old House and Ask This Old House in your area.